PX4的官方文档有简单谈调PID，当然只说了角速度环和角度环，至少你在这里面知道是改哪几个参数。
https://docs.px4.cc/master/zh/config_mc/pid_tuning_guide_multicopter.html
本教程介绍如何在 PX4 上调整 多轴飞行器 (四、六、八旋翼等) 的 PID 参数 。
通常, 如果您使用的是 已经支持的机型 （例如, QGroundControl 中的机身），则默认参数应足以安全地飞行。 为了获得最好的性能, 最好能整定新飞机的 PID 参数。 例如, 不同的电调或电机需要不同的控制增益, 才能获得最佳飞行效果。
本指南仅适用于高级用户。 不合适的参数可能会导致飞行器不稳定，甚至炸机。 确保预先指定保护开关 ( Kill-switch ) 。
PX4 使用 P 比例、 I 积分、 D 微分 (PID) 控制器, 是使用最广泛的控制技术。
The controllers are layered, which means a higher-level controller passes its results to a lower-level controller. The lowest-level controller is the the rate controller, then there is the attitude contoller, and then the velocity & position controller. The PID tuning needs to be done in the same order, starting with the rate controller, as it will affect all other controllers.
PWM_MIN 正确设置。 它需要设置一个小值, 但当飞行器解锁时, 需要保证 电机不停转 。
可以在 特技 Acro 模式 或 手动/自稳模式 中进行测试：
在调参过程中，禁用 MC_AIRMODE。
For safety reasons, the default gains are set to low values. You must increase the gains before you can expect good control responses.
以下是做调参时要遵循的一些一般要点：
角速度控制是最内环的控制器，它用三个独立的PID控制来控制角速度
把角速度控制器调好是非常重要的，因为它会影响到 所有的飞行模式。 角速度控制器跳得好不好可以在位置模式中显现出来，举个例子，你的飞机可能会「抽搐」（飞行器无法很好地悬停在空中）
角速度控制器可以在特技模式或者手动/自稳模式中调整。
MC_ACRO_EXPO = 0, MC_ACRO_EXPO_Y = 0, MC_ACRO_SUPEXPO = 0, MC_ACRO_SUPEXPOY = 0MC_ACRO_P_MAX = 200, MC_ACRO_R_MAX = 200MC_ACRO_Y_MAX = 100万一你的飞行器完全飞不起来，我们给你以下几点建议：
在实际中，手动模式和特技模式的调参套路差不多：一步步地迭代调整滚转和俯仰的P和D增益，然后再调I增益。 Initially you can use the same values for roll and pitch, and once you have good values, you can fine-tune them by looking at roll and pitch response separately (if your vehicle is symmetric, this is not needed). 偏航那就很简单了，四旋翼对偏航角不是很敏感，我们甚至可以直接把偏航的D设为0。
P增益
P增益(比例增益) 用来减小误差。 它可以加快响应速度，因此应该在不引入震荡的前提下设的尽量的高。
D 增益
D增益(微分增益) 用来增加阻尼，可以防止超调。 同样地，这个值应该尽量设大一些来避免超调。
I增益
I（积分）增益可以「记住误差」。 如果你发现过了一段时间了，角速度还是达不到设定值，那就该增加 I 了。 它很重要(尤其在特技模式下) ，但我们不应该把它设得太高。
I 增益一般在0.3~0.5之间，俯仰角的一般要大一点。
测试步骤
要测试现在的增益，可以给一个在悬停状况下给一个脉冲输入（打一下杆再回来）然后观察飞行器的反应。 他应该反应很快，振荡和超调量都不大。(有种「锁定」的感觉)。
You can create a step-input for example for roll, by quickly pushing the roll stick to one side, and then let it go back quickly (be aware that the stick will oscillate too if you just let go of it, because it is spring-loaded — a well-tuned vehicle will follow these oscillations).
一个调得很好的旋翼在特技模式不会随便超某个方向倾斜，即使不做任何矫正也能保持姿态几十秒。
日志
看看日志有助于你看看你调的参咋样。 下面是一份调得比较好的滚转和偏航角速度的日志。
下面这份日志显示了滚转角速度对阶跃输入和脉冲输入的一个比较好的反应。 你可以看到飞行器的超调量非常小。 
角度控制环控制机体的姿态角，并通过设定的角度和实际角度误差来设定期望角速度，反过来想可能会比较直观，即用角速度来补偿角度。该控制环有以下参数可以调：
姿态角控制环调起来就容易多了。 其实大多数时候默认值就够了，完全不用调。
角度控制环可以在手动/自稳模式下调，逐渐增大P增益。 如果看到有振荡或者超调，就说明调得太高了。
下面这几个参数也可以调整 这些参数决定了绕三个轴的最大角速度：
以上的调整都是在悬停油门的基础上的。 但当你增大油门的时候，你可能会看到控制性能又不太好了，机体又开始振荡了。
To counteract that adjust the thrust curve with the THR_MDL_FAC parameter.
The rate controller might need to be re-tuned if you change this parameter.
The mapping from motor control signals (e.g. PWM) to expected thrust is linear by default — setting THR_MDL_FAC to 1 makes it quadratic. Values in between use a linear interpolation of the two. Typical values are between 0.3 and 0.5.
If you have a thrust stand (or can otherwise measure thrust), you can determine the relationship between the PWM control signal and the motor's actual thrust, and fit a function to the data. This Notebook shows how the thrust model factor THR_MDL_FAC may be calculated from previously measured thrust data.
The mapping between PWM and static thrust depends highly on the battery voltage.
If you don't have access to a thrust stand, you can also tune the modeling factor empirically. Start off with 0.3 and increase it by 0.1 at a time. If it is too high, you will start to notice oscillations at lower throttle values. If it is too low you'll notice oscillations at higher throttle values.
The rate controller outputs torque commands for all three axis (roll, pitch and yaw) and a scalar thrust value, which need to be converted into individual motor thrust commands. This step is called mixing.
It can happen that one of the motor commands becomes negative, for example for a low thrust and large roll command (and similarly it can go above 100%). This is a mixer saturation. It is physically impossible for the vehicle to execute these commands (except for reversible motors). PX4 has two modes to resolve this:
Or by increasing (boosting) the commanded thrust, such that none of the motor commands is negative (Airmode enabled). This has the big advantage that the attitude/rates can be tracked correctly even at low or zero throttle. It generally improves the flight performance.
However it increases the total thrust which can lead to situations where the vehicle continues to ascend even though the throttle is reduced to zero. For a well-tuned, correctly functioning vehicle it is not the case, but for example it can happen when the vehicle strongly oscillates due to too high P tuning gains.
Both modes are shown below with a 2D illustration for two motors and a torque command for roll r. On the left motor r is added to the commanded thrust, while on the right motor it is subtracted from it. The motor thrusts are in green. With Airmode enabled, the commanded thrust is increased by b. When it is disabled, r is reduced.
If mixing becomes saturated towards the upper bound the commanded thrust is reduced to ensure that no motor is commanded to deliver more than 100% thrust. This behaviour is similar to the Airmode logic, and is applied whether Airmode is enabled or disabled.
Once your vehicle flies well you can enable Airmode via the MC_AIRMODE parameter.