nanopi2 启动信息

--------------------------------------------------------------------------------
 Second Boot by Nexell Co. : Ver0.6.1 - Built on Oct 16 2015 13:42:17
--------------------------------------------------------------------------------
EMA VALUE : 001
123
Lock value  = 156
GATE CYC    = 0x00008421
GATE CODE   = 0x3B3A3A42
Read  DQ    = 0x08080808
Write DQ    = 0x08080808
Loading from sdmmc...
 Image Loading Done!
Launch to 0x42C00000




U-Boot 2014.07-gb44132b (Jan 19 2016 - 17:35:14)


PLL : [0] =  550000000, [1] =  800000000, [2] =  800000000, [3] =  614399000
PLL1: CPU FCLK =  800000000, HCLK = 200000000
PLL2: BUS BCLK =  400000000, PCLK = 200000000
PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
PLL0: G3D BCLK =  550000000
PLL2: MPG BCLK =  400000000, PCLK = 200000000
I2C:   ready
DRAM:  256 MiB
Heap = 0x43000000~0x45000000
Code = 0x42c00000~0x42c73984
GLD  = 0x42bffeb8
GLBD = 0x42bffe68
SP   = 0x42bffe68,0x42bffe50(CURR)
PC   = 0x42c06114
TAGS = 0x40000100 
PAGE = 0x42c80000~0x42c8c000
MACH = [4330]   
VER  = 1      
BOARD= [nanopi2]    
LCD  = N/A (-1)
MMC:   NXP DWMMC: 0, NXP DWMMC: 1, NXP DWMMC: 2
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
HDMI: display.0, preset 0 (1280 *  720)
HDMI: PHY Ready!!!
DONE: Logo bmp 800 by 480 (3bpp), len=1152056 
DRAW: 0x47000000 -> 0x46000000 
Hit any key to stop autoboot:  0 
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.4.39-s5p4418
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4384096 Bytes = 4.2 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK


Starting kernel ...


[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.39-s5p4418 (txm@ubuntu) (gcc version 4.9.3 (ctng-1.21.0-229g-FA) ) #1 SMP PREEMPT Fri May 27 18:18:16 PDT 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: NANOPI2
[    0.000000] Display: HDMI selected
[    0.000000] nxp_reserve_mem: reserve CMA: size 201326592
[    0.000000] NXP/CMA: Reserved 0x63600000/0x0c000000 for 'ion'
[    0.000000] NXP/CMA: success register cma region for 'ion'
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000
[    0.000000] CPU : iomap[ 1]: p 0xf0000000 -> v 0xf0300000 len=0x100000
[    0.000000] CPU : iomap[ 2]: p 0xcf000000 -> v 0xf0400000 len=0x100000
[    0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000
[    0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000
[    0.000000] CPU : DMA Zone Size =16M, CORE 4
[    0.000000] CPU : VERSION = 2 (0xE153000A), Assign Peripheral Exclusive Bus
[    0.000000] s5p4418-NanoPi2: Board initialized
[    0.000000] CPU : Clock Generator= 64 EA, DVFS = support, PLL.1
[    0.000000] PLL : [0] =  550000000, [1] =  800000000, [2] =  800000000, [3] =  614399000
[    0.000000] PLL1: CPU FCLK =  800000000, HCLK = 200000000
[    0.000000] PLL2: BUS BCLK =  400000000, PCLK = 200000000
[    0.000000] PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
[    0.000000] PLL0: G3D BCLK =  550000000
[    0.000000] PLL2: MPG BCLK =  400000000, PCLK = 200000000
[    0.000000] PERCPU: Embedded 9 pages/cpu @c127a000 s12352 r8192 d16320 u36864
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259839
[    0.000000] Kernel command line: console=ttyAMA0,115200n8 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait init=/sbin/init systemd.show_status=false g_ether.host_addr=82:cf:ce:fa:44:18 initrd=0x49000000,0x400000 console=tty1 lcd=HDMI720P60
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] allocated 2097152 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 1024MB = 1024MB total
[    0.000000] Memory: 825952k/825952k available, 222624k reserved, 272384K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xef800000 - 0xfee00000   ( 246 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef600000   ( 758 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07dfef4   (8032 kB)
[    0.000000]       .init : 0xc07e0000 - 0xc0817040   ( 221 kB)
[    0.000000]       .data : 0xc0818000 - 0xc0896018   ( 505 kB)
[    0.000000]        .bss : 0xc089603c - 0xc0970e98   ( 876 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:288
[    0.000000] VIC @f0002000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f0003000: id 0x00041192, vendor 0x41
[    0.000000] GPIO  @f001a000: start  64, mask 0xffffffff (gpio 53)
[    0.000000] GPIO  @f001b000: start  96, mask 0xffffffff (gpio 54)
[    0.000000] GPIO  @f001c000: start 128, mask 0xffffffff (gpio 55)
[    0.000000] GPIO  @f001d000: start 160, mask 0xffffffff (gpio 56)
[    0.000000] GPIO  @f001e000: start 192, mask 0xffffffff (gpio 57)
[    0.000000] ALIVE @f0010800: start 224, mask 0x000000ff (alive 4)
[    0.000000] GIC   @f0301000: start 256 (vic 31)
[    0.000000] timer.0: source,  10000000(HZ:250), mult:3355443200
[    0.000000] timer.1: event ,  10000000(HZ:250), mult:42949673
[    0.000000] sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 4294967292ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty1] enabled
[    0.000000] Calibrating delay loop... 1594.36 BogoMIPS (lpj=3188736)
[    0.048000] pid_max: default: 32768 minimum: 301
[    0.048000] Security Framework initialized
[    0.048000] SELinux:  Initializing.
[    0.048000] Mount-cache hash table entries: 512
[    0.048000] Initializing cgroup subsys cpuacct
[    0.048000] Initializing cgroup subsys memory
[    0.048000] Initializing cgroup subsys devices
[    0.048000] Initializing cgroup subsys freezer
[    0.048000] CPU: Testing write buffer coherency: ok
[    0.048000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[    0.048000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.048000] Setting up static identity map for 0x405dd9a8 - 0x405dda00
[    0.048000] L310 cache controller enabled
[    0.048000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x70470001, Cache size: 1048576 B
[    0.092000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[    0.132000] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
[    0.172000] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
[    0.176000] Brought up 4 CPUs
[    0.176000] SMP: Total of 4 processors activated (6377.47 BogoMIPS).
[    0.176000] devtmpfs: initialized
[    0.180000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.184000] pwm: max = 50000000 hz
[    0.184000] prepare_gpio_suspend:
[    0.184000]   alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
[    0.184000]   alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
[    0.184000]   alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
[    0.184000]   alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
[    0.184000]   alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
[    0.184000] dummy: 
[    0.184000] NET: Registered protocol family 16
[    0.184000] [Register machine platform devices]
[    0.184000] mach: add amba device uart-pl011.0 
[    0.184000] mach: add amba device uart-pl011.1 
[    0.184000] mach: add amba device uart-pl011.3 
[    0.184000] mach: add amba device uart-pl011.4 
[    0.184000] mach: add amba device pl08xdmac.0 
[    0.184000] mach: add amba device pl08xdmac.1 
[    0.184000] mach: add amba device ssp-pl022.0 
[    0.188000] mach: add device syncgen [2]
[    0.188000] mach: add device hdmi 
[    0.188000] mach: add device i2c bus (array:3) 
[    0.188000] mach: add device Real Time Clock  
[    0.188000] mach: add device generic pwm (array:4)
[    0.188000] mach: add device generic gpio (array:6)
[    0.188000] mach: add device i2s (array:1) 
[    0.188000] mach: add device spdif tx
[    0.188000] mach: add device usb_ehci
[    0.188000] mach: add device usb_ohci
[    0.188000] mach: add device usb otg
[    0.188000] mach: add device ion-nxp
[    0.188000] mach: add device adc
[    0.188000] mach: add graphic device opengl|es
[    0.188000] [Register board platform devices]
[    0.188000] plat: board revision 0
[    0.188000] plat: add dynamic frequency (pll.1)
[    0.188000] plat: add device adc temp
[    0.188000] plat: add framebuffer
[    0.188000] plat: boot from mmc.0
[    0.188000] plat: add device sdmmc [0]
[    0.192000] plat: add device sdmmc [1]
[    0.192000] plat: add device sdmmc [2]
[    0.192000] plat: add backlight pwm device
[    0.192000] plat: add device keypad
[    0.192000] plat: add device fixed voltage
[    0.192000] plat: add device spdif playback
[    0.192000] plat: add device nxp-v4l2
[    0.196000] plat: register spidev
[    0.196000] plat: add touch(ft5x0x) device
[    0.196000] plat: add touch(it7260) device
[    0.196000] plat: add onewire ts device
[    0.196000] plat: add adxl34x device
[    0.196000] plat: add bmp085 device
[    0.196000] plat: add ds1307 device
[    0.196000] plat: add pcf8591 device
[    0.196000] plat: add device gpio_led
[    0.196000] plat: add device pwm_led
[    0.196000] 
[    0.196000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 1
[    0.196000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 2
[    0.196000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 3
[    0.196000] hw-breakpoint: CPU 2 debug is powered down!
[    0.196000] hw-breakpoint: CPU 3 debug is powered down!
[    0.196000] hw-breakpoint: CPU 1 debug is powered down!
[    0.196000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 0
[    0.196000] hw-breakpoint: CPU 0 debug is powered down!
[    0.196000] Serial: AMBA PL011 UART driver
[    0.196000] uart-pl011.0: ttyAMA0 at MMIO 0xc00a1000 (irq = 7) is a PL011 rev3
[    0.200000] console [ttyAMA0] enabled
[    0.204000] uart-pl011.1: ttyAMA1 at MMIO 0xc00a0000 (irq = 6) is a PL011 rev3
[    0.212000] uart-pl011.3: ttyAMA2 at MMIO 0xc00a3000 (irq = 9) is a PL011 rev3
[    0.216000] uart-pl011.4: ttyAMA3 at MMIO 0xc006d000 (irq = 10) is a PL011 rev3
[    0.240000] bio: create slab <bio-0> at 0
[    0.244000] gpiochip_add: registered GPIOs 0 to 31 on device: GPIOA
[    0.248000] gpiochip_add: registered GPIOs 32 to 63 on device: GPIOB
[    0.252000] gpiochip_add: registered GPIOs 64 to 95 on device: GPIOC
[    0.256000] gpiochip_add: registered GPIOs 96 to 127 on device: GPIOD
[    0.260000] gpiochip_add: registered GPIOs 128 to 159 on device: GPIOE
[    0.264000] gpiochip_add: registered GPIOs 160 to 167 on device: GPIOALV
[    0.268000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
[    0.272000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
[    0.276000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
[    0.280000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 1
[    0.284000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
[    0.288000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
[    0.292000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
[    0.296000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 2
[    0.300000] fixed_vdds: 1350 mV 
[    0.304000] nxp_ion_probe success!!!
[    0.308000] SCSI subsystem initialized
[    0.312000] ssp-pl022 ssp-pl022.0: ARM PL022 driver, device ID: 0x00041022
[    0.316000] pl022: mapped registers from 0xc005b000 to f005b000
[    0.320000] ssp-pl022 ssp-pl022.0: setup for DMA on RX dma1chan7, TX dma1chan6
[    0.324000] ssp-pl022 ssp-pl022.0: will use autosuspend for runtime pm, delay 10ms
[    0.328000] usbcore: registered new interface driver usbfs
[    0.332000] usbcore: registered new interface driver hub
[    0.336000] usbcore: registered new device driver usb
[    0.340000] nxp-i2c.0:   390625 hz [pclk=200000000, clk = 256, scale= 1, timeout= 500 ms]
[    0.344000] nxp-i2c.1:    97656 hz [pclk=200000000, clk = 256, scale= 7, timeout= 500 ms]
[    0.352000] nxp-i2c.2:   195312 hz [pclk=200000000, clk = 256, scale= 3, timeout= 500 ms]
[    0.356000] Linux media interface: v0.10
[    0.360000] Linux video capture interface: v2.00
[    0.364000] pps_core: LinuxPPS API ver. 1 registered
[    0.368000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.372000] PTP clock support registered
[    0.376000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.380000] Switching to clocksource source timer
[    0.404000] NET: Registered protocol family 2
[    0.412000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.420000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.428000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.436000] TCP: Hash tables configured (established 131072 bind 65536)
[    0.444000] TCP: reno registered
[    0.444000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.452000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.460000] NET: Registered protocol family 1
[    0.464000] RPC: Registered named UNIX socket transport module.
[    0.468000] RPC: Registered udp transport module.
[    0.476000] RPC: Registered tcp transport module.
[    0.480000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.484000] Unpacking initramfs...
[    0.664000] Initramfs unpacking failed: junk in compressed archive
[    0.680000] Freeing initrd memory: 4096K
[    0.684000] Disply Reset Status : On
[    0.720000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    0.728000] hdmi_get_edid_preset: preferred_preset is supported
[    0.736000] Display HDMI register operation 
[    0.740000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.748000] bt_bcm: rfkill initialized
[    0.752000] audit: initializing netlink socket (disabled)
[    0.756000] type=2000 audit(0.756:1): initialized
[    0.764000] highmem bounce pool size: 64 pages
[    0.776000] NFS: Registering the id_resolver key type
[    0.780000] fuse init (API version 7.18)
[    0.784000] msgmni has been set to 1089
[    0.792000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.800000] io scheduler noop registered
[    0.804000] io scheduler deadline registered
[    0.808000] io scheduler cfq registered (default)
[    0.812000] display.0 connected to fb.0  ...
[    0.816000] nxp-fb.0: dma addr = 0x63600000, buf[0xe2912c00]
[    0.820000] nxp-fb.0: dma addr = 0x63984000, buf[0xe2912dc0]
[    0.872000] hdmi_stop entered
[    0.876000] hdmi_run entered
[    0.888000] HDMI PHY Ready!!!
[    0.892000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.900000] _calc_hdmi_sync_param: _h_sync_offset 0
[    0.928000] hdmi_run exit
[    0.928000] nxp-fb 0: out[0], 1280 * 720 - 32 bpp (phys:63600000 virt:0xef831000 max:7372800)
[    0.952000] Console: switching to colour frame buffer device 160x45
[    0.984000] uart-pl011 uart-pl011.0: no DMA platform data
[    0.988000] uart-pl011 uart-pl011.1: no DMA platform data
[    0.992000] uart-pl011 uart-pl011.3: no DMA platform data
[    1.000000] uart-pl011 uart-pl011.4: no DMA platform data
[    1.008000] loop: module loaded
[    1.012000] tun: Universal TUN/TAP device driver, 1.6
[    1.016000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.024000] PPP generic driver version 2.4.2
[    1.028000] PPP BSD Compression module registered
[    1.032000] PPP Deflate Compression module registered
[    1.048000] PPP MPPE Compression module registered
[    1.052000] NET: Registered protocol family 24
[    1.056000] usbcore: registered new interface driver asix
[    1.064000] usbcore: registered new interface driver cdc_ether
[    1.068000] usbcore: registered new interface driver net1080
[    1.080000] usbcore: registered new interface driver cdc_subset
[    1.088000] usbcore: registered new interface driver zaurus
[    1.100000] usbcore: registered new interface driver cdc_ncm
[    1.108000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.120000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
[    1.128000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
[    1.140000] nxp-ehci nxp-ehci: irq 50, io mem 0xc0030000
[    1.160000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
[    1.168000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.180000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.188000] usb usb1: Product: SLsi Synopsys EHCI Host Controller
[    1.200000] usb usb1: Manufacturer: Linux 3.4.39-s5p4418 ehci_hcd
[    1.208000] usb usb1: SerialNumber: nxp-ehci
[    1.220000] hub 1-0:1.0: USB hub found
[    1.228000] hub 1-0:1.0: 3 ports detected
[    1.236000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.444000] Core Release: 2.93a
[    1.452000] Setting default values for core params
[    1.460000] Finished setting default values for core params
[    1.548000] usb 1-1: new high-speed USB device number 2 using nxp-ehci
[    1.672000] Using Descriptor DMA mode
[    1.680000] Dedicated Tx FIFOs mode
[    1.688000] dwc_otg dwc_otg: DWC OTG Controller
[    1.688000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    1.688000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.688000] usb 1-1: Product: USB2.0 Hub
[    1.688000] hub 1-1:1.0: USB hub found
[    1.688000] hub 1-1:1.0: 4 ports detected
[    1.704000] HDMI HPD State 0x1
[    1.732000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    1.732000] _hdmi_hpd_changed: edid update success, preset 18
[    1.732000] notify_hpd_changed: state 1
[    1.732000] hdmi_run entered
[    1.732000] hdmi_run: hdmi already running!
[    1.792000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
[    1.804000] dwc_otg dwc_otg: irq 49, io mem 0x00000000
[    1.816000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.824000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.836000] usb usb2: Product: DWC OTG Controller
[    1.844000] usb usb2: Manufacturer: Linux 3.4.39-s5p4418 dwc_otg_hcd
[    1.856000] usb usb2: SerialNumber: dwc_otg
[    1.864000] hub 2-0:1.0: USB hub found
[    1.872000] hub 2-0:1.0: 1 port detected
[    1.880000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.892000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
[    1.904000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
[    1.916000] nxp-ohci nxp-ohci: irq 50, io mem 0xc0020000
[    1.964000] usb 1-1.1: new low-speed USB device number 3 using nxp-ehci
[    1.984000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.992000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.004000] usb usb3: Product: SLsi Synopsys OHCI Host Controller
[    2.016000] usb usb3: Manufacturer: Linux 3.4.39-s5p4418 ohci_hcd
[    2.028000] usb usb3: SerialNumber: nxp-ohci
[    2.036000] hub 3-0:1.0: USB hub found
[    2.044000] hub 3-0:1.0: 3 ports detected
[    2.052000] Initializing USB Mass Storage driver...
[    2.064000] usbcore: registered new interface driver usb-storage
[    2.068000] usb 1-1.1: New USB device found, idVendor=0101, idProduct=0007
[    2.068000] usb 1-1.1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.068000] usb 1-1.1: Product: USB OPTICAL MOUSE 
[    2.108000] USB Mass Storage support registered.
[    2.116000] usbcore: registered new interface driver usbserial
[    2.128000] usbcore: registered new interface driver usbserial_generic
[    2.136000] USB Serial support registered for generic
[    2.144000] usb 1-1.4: new low-speed USB device number 4 using nxp-ehci
[    2.240000] usb 1-1.4: New USB device found, idVendor=1c4f, idProduct=0002
[    2.252000] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.264000] usb 1-1.4: Product: USB Keyboard
[    2.272000] usb 1-1.4: Manufacturer: SIGMACHIP
[    2.284000] usbserial: USB Serial Driver core
[    2.292000] usbcore: registered new interface driver ftdi_sio
[    2.304000] USB Serial support registered for FTDI USB Serial Device
[    2.316000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[    2.324000] usbcore: registered new interface driver option
[    2.336000] USB Serial support registered for GSM modem (1-port)
[    2.348000] usbcore: registered new interface driver pl2303
[    2.356000] USB Serial support registered for pl2303
[    2.368000] g_ether gadget: using random self ethernet address
[    2.376000] usb0: MAC be:6d:d1:fb:c2:d5
[    2.388000] usb0: HOST MAC 82:cf:ce:fa:44:18
[    2.396000] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[    2.408000] g_ether gadget: g_ether ready
[    2.416000] mousedev: PS/2 mouse device common for all mice
[    2.428000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
[    2.440000] usbcore: registered new interface driver xpad
[    2.448000] i2c-core: driver [IT7260-ts] using legacy suspend method
[    2.460000] i2c-core: driver [IT7260-ts] using legacy resume method
[    2.472000] touchscreen-1wire initialized
[    2.480000] backlight-1wire initialized
[    2.488000] input: fa_ts_input as /devices/virtual/input/input1
[    2.500000] ts-if initialized
[    2.508000] [RTC] day=2016.01.07 time=00:12:43
[    2.520000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
[    2.528000] i2c /dev entries driver
[    2.540000] lirc_dev: IR Remote Control driver registered, major 248 
[    2.548000] IR NEC protocol handler initialized
[    2.560000] IR RC5(x) protocol handler initialized
[    2.568000] IR RC6 protocol handler initialized
[    2.576000] IR JVC protocol handler initialized
[    2.588000] IR Sony protocol handler initialized
[    2.596000] IR RC5 (streamzap) protocol handler initialized
[    2.608000] IR SANYO protocol handler initialized
[    2.616000] IR LIRC bridge handler initialized
[    2.624000] gspca_main: v2.14.0 registered
[    2.640000] ...................................ov5640_probe 2234
[    2.652000] ...................................ov5640_video_probe 2193
[    2.660000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
[    2.672000] i2c.0 addr 0x78 (try:1)
[    2.680000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
[    2.692000] i2c.0 addr 0x78 (try:2)
[    2.700000] Error: i2c.0, addr:78, trans len:-11(2), try:2
[    2.712000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
[    2.720000] i2c.0 addr 0x78 (try:1)
[    2.728000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
[    2.740000] i2c.0 addr 0x78 (try:2)
[    2.748000] Error: i2c.0, addr:78, trans len:-11(2), try:2
[    2.760000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
[    2.772000] i2c.0 addr 0x78 (try:1)
[    2.780000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
[    2.792000] i2c.0 addr 0x78 (try:2)
[    2.800000] Error: i2c.0, addr:78, trans len:-11(2), try:2
[    2.808000] ov5640 0-003c: reg_read: i2c read error, reg: 300a
[    2.820000] OV5640 read error!!!!!!!!!!!!!!!
[    2.828000] ov5640_initialize_ctrls.............1794...........
[    2.840000] usbcore: registered new interface driver uvcvideo
[    2.852000] USB Video Class driver (1.1.1)
[    2.860000] Driver for 1-wire Dallas network protocol.
[    2.872000] device-mapper: uevent: version 1.0.3
[    2.880000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    2.896000] DVFS: ASV[0] IDS(10mA,  9) Ro(110, 98)
[    2.904000] DVFS: regulator vdd_arm_1.3V
[    2.912000] DVFS: cpu DVFS with PLL.1 [tables=8]
[    2.924000] cpuidle: using governor ladder
[    2.932000] cpuidle: using governor menu
[    2.940000] Synopsys Designware Multimedia Card Interface Driver
[    2.948000] dw_mmc dw_mmc.0: Using internal DMA controller.
[    2.960000] mmc0: no vmmc regulator found
[    2.968000] dw_mmc dw_mmc.0: Using external card detect irq 225 (io 161)
[    2.976000] dw_mmc dw_mmc.0: Version ID is 250a
[    2.984000] dw_mmc dw_mmc.0: DW MMC controller at irq 43, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    2.992000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    3.008000] dw_mmc dw_mmc.1: Using internal DMA controller.
[    3.020000] mmc1: no vmmc regulator found
[    3.028000] dw_mmc dw_mmc.1: Version ID is 250a
[    3.036000] dw_mmc dw_mmc.1: DW MMC controller at irq 44, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    3.048000] dw_mmc dw_mmc.2: Using internal DMA controller.
[    3.056000] mmc2: no vmmc regulator found
[    3.064000] dw_mmc dw_mmc.2: Using external card detect irq 152 (io 88)
[    3.076000] dw_mmc dw_mmc.2: Version ID is 250a
[    3.080000] dw_mmc dw_mmc.2: DW MMC controller at irq 45, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    3.084000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    3.084000] mmc0: new high speed SDHC card at address aaaa
[    3.084000] mmcblk0: mmc0:aaaa SL08G 7.40 GiB 
[    3.084000]  mmcblk0: p1 p2
[    3.104000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    3.148000] input: USB OPTICAL MOUSE  as /devices/platform/nxp-ehci/usb1/1-1/1-1.1/1-1.1:1.0/input/input2
[    3.152000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 300000Hz, actual 297619HZ div = 84)
[    3.172000] generic-usb 0003:0101:0007.0001: input,hidraw0: USB HID v1.11 Mouse [USB OPTICAL MOUSE ] on usb-nxp-ehci-1.1/input0
[    3.192000] input: SIGMACHIP USB Keyboard as /devices/platform/nxp-ehci/usb1/1-1/1-1.4/1-1.4:1.0/input/input3
[    3.204000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 200000Hz, actual 200000HZ div = 125)
[    3.204000] generic-usb 0003:1C4F:0002.0002: input,hidraw1: USB HID v1.10 Keyboard [SIGMACHIP USB Keyboard] on usb-nxp-ehci-1.4/input0
[    3.208000] input: SIGMACHIP USB Keyboard as /devices/platform/nxp-ehci/usb1/1-1/1-1.4/1-1.4:1.1/input/input4
[    3.208000] generic-usb 0003:1C4F:0002.0003: input,hidraw2: USB HID v1.10 Device [SIGMACHIP USB Keyboard] on usb-nxp-ehci-1.4/input1
[    3.208000] usbcore: registered new interface driver usbhid
[    3.208000] usbhid: USB HID core driver
[    3.208000] ADC: CHs 8, 200000(1000000 ~ 130208) sample rate, polling mode, scale=166(bit 6)
[    3.212000] snd pcm: register sound platform 'nxp-pcm'
[    3.212000] snd i2s: ch 0, master, iis mode, 48000(47999)hz, 32 FBITs, MCLK=12287980hz, RFS=256
[    3.212000] spdif-tx: 48000(47348)Hz, MCLK=12121212hz HDMI out
[    3.212000] asoc: dit-hifi <-> nxp-spdif-tx mapping ok
[    3.212000] GACT probability NOT on
[    3.212000] Mirror/redirect action on
[    3.212000] u32 classifier
[    3.212000]     Actions configured
[    3.212000] Netfilter messages via NETLINK v0.30.
[    3.212000] nf_conntrack version 0.5.0 (12969 buckets, 51876 max)
[    3.216000] ctnetlink v0.93: registering with nfnetlink.
[    3.216000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    3.216000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    3.216000] xt_time: kernel timezone is -0000
[    3.216000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.216000] arp_tables: (C) 2002 David S. Miller
[    3.216000] TCP: cubic registered
[    3.216000] Initializing XFRM netlink socket
[    3.216000] NET: Registered protocol family 10
[    3.216000] Mobile IPv6
[    3.216000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    3.216000] IPv6 over IPv4 tunneling driver
[    3.216000] NET: Registered protocol family 17
[    3.216000] NET: Registered protocol family 15
[    3.216000] NET: Registered protocol family 35
[    3.216000] Registering the dns_resolver key type
[    3.216000] Registering SWP/SWPB emulation handler
[    3.216000] otg_wakelock_init: No USB transceiver found
[    3.532000] nxp-rtc nxp-rtc.0: setting system clock to 2016-01-07 00:12:44 UTC (1452125564)
[    3.532000] TMU: register adc.2 to hwmon
[    3.532000] ALSA device list:
[    3.532000]   #0: SPDIF-Transciever
[    3.564000] Freeing init memory: 220K
[    3.572000] Write protecting the kernel text section c0008000 - c07b2000
[    3.580000] rodata_test: attempting to write to read-only section:
[    3.584000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 100000Hz, actual 100000HZ div = 250)
[    3.604000] write to read-only section trapped, success
[    5.084000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    5.120000] EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
[    5.684000] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[    5.708000] systemd[1]: Detected architecture 'arm'.
[    5.724000] systemd[1]: Set hostname to <NanoPi2>.
ÿ[    6.128000] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    6.148000] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    6.156000] systemd[1]: Expecting device dev-ttyAMA0.device...
[    6.168000] systemd[1]: Starting Remote File Systems (Pre).
[    6.176000] systemd[1]: Reached target Remote File Systems (Pre).
[    6.184000] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[    6.196000] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    6.208000] systemd[1]: Starting Paths.
[    6.212000] systemd[1]: Reached target Paths.
[    6.220000] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[    6.232000] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    6.248000] systemd[1]: Starting Encrypted Volumes.
[    6.256000] systemd[1]: Reached target Encrypted Volumes.
[    6.264000] systemd[1]: Starting Swap.
[    6.272000] systemd[1]: Reached target Swap.
[    6.276000] systemd[1]: Starting Root Slice.
[    6.284000] systemd[1]: Created slice Root Slice.
[    6.292000] systemd[1]: Starting User and Session Slice.
[    6.304000] systemd[1]: Created slice User and Session Slice.
[    6.312000] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[    6.320000] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    6.332000] systemd[1]: Starting Delayed Shutdown Socket.
[    6.340000] systemd[1]: Listening on Delayed Shutdown Socket.
[    6.348000] systemd[1]: Starting Journal Socket (/dev/log).
[    6.360000] systemd[1]: Listening on Journal Socket (/dev/log).
[    6.368000] systemd[1]: Starting udev Control Socket.
[    6.376000] systemd[1]: Listening on udev Control Socket.
[    6.384000] systemd[1]: Starting udev Kernel Socket.
[    6.392000] systemd[1]: Listening on udev Kernel Socket.
[    6.400000] systemd[1]: Starting Journal Socket.
[    6.408000] systemd[1]: Listening on Journal Socket.
[    6.416000] systemd[1]: Starting System Slice.
[    6.424000] systemd[1]: Created slice System Slice.
[    6.432000] systemd[1]: Starting system-getty.slice.
[    6.440000] systemd[1]: Created slice system-getty.slice.
[    6.448000] systemd[1]: Starting system-serial\x2dgetty.slice.
[    6.456000] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    6.468000] systemd[1]: Starting Increase datagram queue length...
[    6.476000] systemd[1]: Starting Nameserver information manager...
[    6.488000] systemd[1]: Mounted Huge Pages File System.
[    6.496000] systemd[1]: Mounted POSIX Message Queue File System.
[    6.516000] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    6.532000] systemd[1]: Mounting Debug File System...
[    6.548000] systemd[1]: Started Set Up Additional Binary Formats.
[    6.560000] systemd[1]: Starting Load Kernel Modules...
[    6.568000] systemd[1]: Starting udev Coldplug all Devices...
[    6.580000] systemd[1]: Starting Slices.
[    6.584000] systemd[1]: Reached target Slices.
[    6.592000] systemd[1]: Mounted Debug File System.
[    6.624000] Loading modules backported from Linux version v4.4.2-0-g1cb8570
[    6.628000] systemd[1]: Started Increase datagram queue length.
[    6.644000] Backport generated by backports.git v4.4.2-1-0-gbec4037
[    6.684000] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    6.708000] systemd[1]: Starting Create Static Device Nodes in /dev...
[    6.720000] systemd[1]: Starting Syslog Socket.
[    6.728000] systemd[1]: Listening on Syslog Socket.
[    6.736000] systemd[1]: Starting Journal Service...
[    6.748000] systemd[1]: Started Journal Service.
[    6.916000] systemd-udevd[191]: starting version 215
[    7.080000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    7.132000] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    7.144000] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    7.156000] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    7.168000] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    7.188000] systemd-journald[183]: Received request to flush runtime journal from PID 1
[    7.280000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    7.296000] mmc1: new high speed SDIO card at address 0001
[    7.340000] wl_create_event_handler(): thread:wl_event_handler:ff started
[    7.352000] dhd_attach(): thread:dhd_watchdog_thread:100 started
[    7.360000] dhd_attach(): thread:dhd_dpc:101 started
[    7.368000] dhd_attach(): thread:dhd_rxf:102 started
[    7.512000] cfg80211: World regulatory domain updated:
[    7.520000] cfg80211:  DFS Master region: unset
[    7.524000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[    7.548000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    7.556000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    7.556000] Bluetooth: Core ver 2.21
[    7.556000] NET: Registered protocol family 31
[    7.556000] Bluetooth: HCI device and connection manager initialized
[    7.556000] Bluetooth: HCI socket layer initialized
[    7.556000] Bluetooth: L2CAP socket layer initialized
[    7.556000] Bluetooth: SCO socket layer initialized
[    7.616000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[    7.628000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[    7.640000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[    7.652000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[    7.652000] Bluetooth: HCI UART driver ver 2.3
[    7.652000] Bluetooth: HCI UART protocol H4 registered
[    7.652000] Bluetooth: HCI UART protocol BCM registered
[    7.652000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    7.652000] Bluetooth: BNEP filters: protocol multicast
[    7.652000] Bluetooth: BNEP socket layer initialized
[    7.652000] setting PHY_BASEADDR_POWER_GATE, set 1
[    7.652000] setting PHY_BASEADDR_PMU_ISOLATE+4, set 0
[    7.652000] setting PHY_BASEADDR_PMU_ISOLATE+8, set 0
[    7.652000] setting PHY_BASEADDR_PMU_ISOLATE, set 1
[    7.652000] read PHY_BASEADDR_PMU_ISOLATE + 0xC
[    7.652000] Wait Power UP Ack(powerUpAck=0x00000000)
[    7.652000] setting ClockGen, set 1
[    7.652000] setting Reset VR addr(0xf0012008)
[    7.652000] setting PHY_BASEADDR_VR_PMU addr(0xf0072000)
[    7.652000] Vr: VR device driver loaded(ver1.2) for s5p4418
[    7.784000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    7.796000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[    8.036000] bt_bcm: rfkill set_block On  GPIOB.8
[    8.716000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 98040Hz, actual 98039HZ div = 255)
[    8.772000] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    8.784000] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    8.800000] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    8.816000] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    9.156000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    9.608000] bt_bcm: rfkill set_block Off GPIOB.8
[    9.688000] bt_bcm: rfkill set_block On  GPIOB.8
[    9.848000] cfg80211: Regulatory domain changed to country: CN
[    9.864000] cfg80211:  DFS Master region: FCC
[    9.868000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[    9.884000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    9.892000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[    9.904000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[    9.916000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[    9.928000] cfg80211:   (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
[    9.940000] cfg80211:   (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400 mBm), (N/A)
[    9.956000] cfg80211:   (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
ÿÿÿÿÿÿ
Debian GNU/Linux 8 NanoPi2 ttyAMA0


NanoPi2 login: [   19.872000] EXT4-fs (mmcblk0p1): recovery complete
[   19.880000] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)