详见 http://www.thinkwiki.org/wiki/Tp_smapi
安装tp-smapi:
# aptitude install tp-smapi-dkms
# modprobe tp_smapi
更改充电阈值：
设置开始充电阈值，如从“60%”开始充电：
# echo 60 >
/sys/devices/platform/smapi/BAT0/start_charge_thresh
设置停止充电阈值，如到“100%”停止充电：
# echo 100 >
/sys/devices/platform/smapi/BAT0/stop_charge_thresh
查看充电阈值：
# cat /sys/devices/platform/smapi/BAT0/*_charge_thresh
其他：
To prevent charging for 17 minutes (regardless of
thresholds):
# echo 17 >
/sys/devices/platform/smapi/BAT0/inhibit_charge_minutes
To cancel charging preventation:
# echo 0 >
/sys/devices/platform/smapi/BAT0/inhibit_charge_minutes
To force battery discharging (even if connected to AC):
# echo 1 >
/sys/devices/platform/smapi/BAT0/force_discharge
To cancel forced discharge:
# echo 0 >
/sys/devices/platform/smapi/BAT0/force_discharge
让设置在启动时生效(只用同一块电池)：
It is not necessary to create your own init.d script or modify
/etc/rc.local - you just need the package sysfsutils:
# apt-get install sysfsutils
# sudo gedit /etc/sysfs.conf
把下面的放在文件 /etc/sysfs.conf后面:
# cat >> /etc/sysfs.conf
<< EOF
# For a LiIon battery in a Thinkpad
devices/platform/smapi/BAT0/start_charge_thresh = 50
devices/platform/smapi/BAT0/stop_charge_thresh = 80
EOF
The init script supplied by sysfsutils will load these
settings on each boot.
其他电池状态信息：
To view extended battery status such as charging state,
voltage, current, capacity, cycle count and model
information:
# cat /sys/devices/platform/smapi/BAT0/installed
# cat /sys/devices/platform/smapi/BAT0/state
#
idle/charging/discharging
# cat /sys/devices/platform/smapi/BAT0/cycle_count
# cat /sys/devices/platform/smapi/BAT0/current_now #
instantaneous current
# cat /sys/devices/platform/smapi/BAT0/current_avg # last
minute average
# cat /sys/devices/platform/smapi/BAT0/power_now
# instantaneous power
# cat /sys/devices/platform/smapi/BAT0/power_avg
# last minute average
# cat
/sys/devices/platform/smapi/BAT0/last_full_capacity
# cat /sys/devices/platform/smapi/BAT0/remaining_percent
# cat
/sys/devices/platform/smapi/BAT0/remaining_running_time
# cat
/sys/devices/platform/smapi/BAT0/remaining_charging_time
# cat
/sys/devices/platform/smapi/BAT0/remaining_capacity
# cat /sys/devices/platform/smapi/BAT0/design_capacity
# cat /sys/devices/platform/smapi/BAT0/voltage
# cat /sys/devices/platform/smapi/BAT0/design_voltage
# cat /sys/devices/platform/smapi/BAT0/manufacturer
# cat /sys/devices/platform/smapi/BAT0/model
# cat /sys/devices/platform/smapi/BAT0/barcoding
# cat /sys/devices/platform/smapi/BAT0/chemistry
# cat /sys/devices/platform/smapi/BAT0/serial
# cat /sys/devices/platform/smapi/BAT0/manufacture_date
# cat /sys/devices/platform/smapi/BAT0/first_use_date
# cat /sys/devices/platform/smapi/BAT0/temperature # in
milli-Celsius
# cat /sys/devices/platform/smapi/ac_connected
The raw status data is also available, including some fields
not listed above (in case you can figure them out):
# cat /sys/devices/platform/smapi/BAT0/dump
